각종 공구류/악세서리
전동 모터 악세서리
기타 악세서리

 - 기술자료실

 - A/S문의및처리게시판

 - 사진자료실
 - 동영상자료실

고객 상담 :
PM 2 - 8시

배송 마감 :
      PM 4시

   충전기/측정기 >Checker/Balancer
  [Matek] 3in1 Battery Monitor & Discovery Buzzer & Signal Loss Alarm

   상품명 [Matek] 3in1 Battery Monitor & Discovery Buzzer & Signal Loss Alarm
 상품가격 6,800원 68원
 상품코드 SRBC-007
 제조회사 Matek
 제조국 중국


[Matek] 3in1 Battery Monitor & Discovery Buzzer & Signal Loss Alarm

Matek사의 3in1 배터리 모니터 및 분실 방지용 부저 / 시그널 Lost 알람 세트.



- Working voltage: 5.2~26V DC, 2~6Cells LiPo
- Standby current less than 10mA
- Working current, Max 120mA (blinking & beeping)
- Voltage threshold setting: 3.4~3.7V/cell (Red LED)
- Twin loud buzzers, 85db each
- Ultrahigh Brightness LED, 20lm, 0.2w, Blue
- Size: 20x30x6mm,
- Weight: 7g (Including Wires)

<How to use>

1. Battery monitor function (F1)

It can monitor 2~6S LiPo voltage status & notify you once the cells reach the defined voltage.
The voltage threshold of alarm & flash can be customized between 3.4V~3.7V/Cell.

1.1 If the LiPo voltage is in the range of following, The BM3in1 will detect the cell numbers automatically when the LiPo is connected.

     7.4~8.6V: 2cells LiPo
    11.1~12.9V: 3cells LiPo
    14.8~17.2V: 4cells LiPo
    18.5~21.5V: 5cells LiPo
    22.2~25.8V: 6cells LiPo

The BM3in1 will alarm “Be” & the voltage threshold red LED will be shown.

Hold the button 3 seconds to enter the setting of the voltage threshold.
Press button to set the alarm threshold between 3.4~3.7V/Cell(red LED) .
The value will be saved & exit if no action within 10 seconds.
During the using of LiPo, BM3in1 will detect the voltage always.
If the total voltage is below “threshold * cells”, the alarm & blink will be triggered with “Be..Be..Be……”
If the total voltage rise again, the alarm & blink will be suspended.

1.2 If the LiPo voltage is out of the aforesaid range. The BM3in1 will alarm “Be..Be..Be” & 4 red LEDs light. Pls check if the battery total voltage is below 3.7V*cells

2. Discovery buzzer function (F2)

It is easy to use the function, Just plug it in one Aux channel(e.g. Gear).
Move the toggle switch to one side or another side, the BM3in1 will alarm “BeBeBeBeBe” & blue LED blink.

3. Signal loss alarm function (F3)

It can warn you if you turn off the transmitter first by mistake, if you have trouble finding a model in the long grass…
Turn on the transmitter first. Hook BM3in1 to the receiver THRO channel, then plug battery into model. It will detect the loss of TX signal, and emit a loud alarm “BeBe…BeBe…BeBe…” & the blue LED blink.
RX power on, the alarm & blink will be triggered as following
Turn off the transmitter first. and keep one minute.

The radio power on, but no action of stick or no signal change within one minute.

[TR] BX-200 Battery 통합 관리 모듈 (1S~7S)
[TR] BX-100 Li-Po Battery Voltage Tester & Low Voltage Buzzer ALARM(1S~8S/3.7V~29.6V)
[PT] Battery Tester (1S~6S/3.7V~22.2V)
[Po8er] CellMeter-8 (1S~8S/배터리 잔량 및 전압 체커기)
[Po8er] CellMeter-7 (1S~7S/배터리 잔량 및 전압 체커기)



작성자 비밀번호
  • 회원인 분은 먼저 로그인 부탁 드립니다.


    - 경기도 성남시 중원구 사기막골로 124 (상대원동, SKn테크노파크) 테크동 308호 ALIGN KOREA  
    - 사업자등록번호 : 129-25-18013  | 경기성남2007-902호
    - 문의전화 : 031-719-6371   |  팩스 : 031-776-3061 | 대표 : 박철훈
    - Copyright ⓒ 2005 전동알씨. All rights reserved. Send comments regarding this to rolandpark@empas.com
     ★ 본 사이트의 제품 이미지나 글의 무단도용시 법적조치를 받을수있습니다.